The bathroom is the main part of the decoration. The ceramic sanitary ware is the most critical product of the bathroom. Its purchase and support are particularly important.
The main varieties of ceramic sanitary ware are toilets, bidets, facial washers, sinks, mop pools, hand carton boxes, soap boxes, etc. Currently, there are many brands of ceramic sanitary ware on the market, and there are large differences in quality grades, and there is a wide range of price differences. When purchasing, you should first have a sense of support, first determine the standards you expect to reach, and each component or accessory in the kit should be at the same level.
Determine the toilet drainage method and installation size
Before purchasing the toilet, be sure to measure the distance from the center of the outlet to the wall surface (down drainage method) or the distance from the floor surface (post-drainage method) to determine whether the selected toilet is a drainage or rear drainage structure. The method is consistent and the size of the toilet is suitable for installation. The wall spacing of the toilet drain outlet should be equal to or slightly smaller than the wall distance of the toilet outlet (down drainage method); the distance from the toilet drainage outlet to the ground should be equal to or slightly higher than the height of the toilet drainage outlet (after drainage).
Matching product style tone must match
The number of ceramic pieces in the bathroom is more than one, and the number of ceramic products such as toilet bowls, wash basins, soap boxes, hand paper boxes, and mop pools can only be consistent or close to harmony and beauty.
Carefully select the visible surface
The selection of ceramic sanitary ware should have different requirements for the visible surface and the non-visible surface: The visible surface refers to the surface that is easy to see after the porcelain is installed, and the quality of the visible surface should be strictly controlled, especially when the water is splashed when used. The quality of the parts is more important, and the quality of the invisible surfaces after installation should not be too picky.
Ceramic sanitary ware appearance quality three judgments
(1) Whether there is cracking: tapping the edge of the porcelain piece with a thin rod to listen to the sound is crisp, when there is a 'husky' sound, it proves that the porcelain pieces have cracks.
(2) Deformation size: Put the porcelain pieces on a flat platform, check whether the movement is smooth and even in all directions, whether the installation surface and the edge of the porcelain surface are flat and whether the installation holes are even and smooth.
(3) Glaze quality: The glaze must be smooth and smooth, and the glaze should be uniform. Visible surface, especially the quality of glazed water splashing is especially important. Drop a few drops of colored liquid on the glaze with a cloth to wipe it evenly. After a few seconds, use a damp cloth to dry it. Check the glaze and no dirty spots are better.
Ceramic sanitary ware also has water absorption, toilets have drainage, water consumption, noise, water seal function and other performance requirements, these performance consumers are generally difficult to check and judge, should try to buy products with quality credit guarantee, check the The product is certified by the relevant national authorities and has a recent effective quality inspection report with the CMA chapter.
Bay window decoration entrance decoration style decoration style bathroom door size bathroom size bathroom door
Overshot go into the heart of the drill pipe, the slider move up, make the tube socket head can be inserted into the center, when on the slider move up tight, using friction lift drill, remove loose again after the slider, by means of the connection string to slide along the block should tighten, set aside the center pipe, but in front of the salvage must first determine the bit in the bottom of the hole position, can be in a thin plate with bolts tight end of drill pipe, Drop the drill pipe to the bottom of the hole and press it on the drill bit. After waiting for a moment, it is proposed that the relative position of the drill bit at the bottom of the hole and the center of the rotary plate of the drill can be determined by observing the indentation left by the center pipe of the drill bit on the board, and then move the drill or rotary plate so that the center of the rotary plate is directly in front of the center pipe of the injured head, so as to ensure that the fishing device can be inserted into the center pipe accurately.
Overshot Assembly,Fishing Tools,Overshot Assembly For Sale,Overshot Fishing Assembly
WUXI XINZUAN GEOLOGICAL EQUIPMENT CO.,LTD. , https://www.wxsmrxz.com