In the decoration of the sanitary area, many people will focus on the layout of water and electricity, waterproof construction, and the arrangement and purchase of sanitary ware. However, the installation of ceilings here is also very important. Take the relationship between water heaters and suspended ceilings, they are closely linked. So many people are entangled, which is the first installation of ceiling and water heater? Today Xiao Bian came to explain to you about the ceiling and water heater which first installed knowledge, together to understand it!
Ceiling and water heater which first installed 1
From the perspective of the installer, it would be more convenient to install the ceilings first, so that they would be less difficult to construct and easier to operate. However, if this is done, it is necessary to reserve the location of the water heater and the point where the water heater is installed in advance, and there are generally two hooks behind the water heater. The distance between the two hooks needs to be measured, and then the length and width of the water heater are determined. . If this distance is not accurate, it will directly affect the aesthetics of the entire bathroom and the installation of the water heater.
Ceiling and water heater which first installed 2
Also from the perspective of the installer, if the water heater is installed first, it will test the master's skill and skill. In general, if the water heater is installed first, it will be very inconvenient to install the ceiling afterwards, and there will be a certain gap, which will directly affect the overall aesthetics. If your master is skilled, then the effect will be very good after completion.
Ceiling and water heater which first installed 3
If viewed from top to bottom, the ceiling is at the top and the water heater is below the ceiling. If the water heater is installed first, it would be very inconvenient to install the ceiling, and the water heater would become a stumbling block. And it will also waste the installation time of the master and delay your schedule.
Ceiling and water heater which first installed 4
In general, it is better to do the ceiling first. We should follow the order of decoration in the sanitary area, that is, "from the top down." Of course, if you want to hide the water heater inside the ceiling, then you need to install the water heater first, so that the water heater's location is better and the gap in the ceiling will not appear too large.
Xiao Bian's words: These two procedures are important steps in the renovation of the bathroom area. If you still want to focus on aesthetics, then you may choose to combine the water heater and the ceiling, that is, wrap the water heater in the ceiling. Although there will be a gap between the suspended ceiling and the water heater in the middle of the sewer pipe, the average master can control it, but the floor height of the interior will be directly reduced. The above is Xiaobian and everyone to explain the ceiling and water heater which first installed the knowledge, and hope to give you some reference! More related content, you can pay attention to Qijia information, follow-up will present more exciting content!
Ceiling and water heater which first installed
Reflective warning`s reflection part of the vest is the use of lattice micro-rhombus type refraction and high refractive index of glass beads back to the principle of reflection, through the post-processing of advanced processing technology made. It can reflect the distant light back to the light. Both in the day or night have a good retroreflective optical performance. Especially at night, it can play the same high visibility as the day. The use of this high-energy reflective material made of safety clothing, whether the wearer is in the distance, or in the light or scattered light interference, it can be relatively easy to be found by the night driver.
Reflective warning vests are made of high-visibility reflective material It can make the traffic police work smoothly in the night or special weather in order to reduce the rate of the casualties. it plays a special role in security especially in traffic engineering.When the motor vehicle fails, the driver needs to wear a reflective warning vest, and away from the faulty vehicle to prevent the occurrence of secondary accidents. This kind of reflective warning vest is mainly applicable to police, road officials, traffic commanders, road maintenance personnel, motorists, motorcycles and bicycles drivers, dark light workers and so on in one word, the local worker who needs to use light warning. Widely used in traffic engineering, shipbuilding industry, steel industry, machinery industry, oil industry, ambulance, parking lot, airport, traffic police and outdoor work or construction, plays an important role in good security warning .
When Car Reflective Vest use the aluminum lattice reflective material, not only in a small angle (from the reflective warning vest wearer far away), reflective brightness is high, even at a large angle (from the reflective warning vest wearer closer ), it still has a good reflective brightness, so that the locomotive driver earlier identified roadside vehicle side of the staff, as soon as possible to respond to effectively prevent the occurrence of secondary accidents.
According to reflective vest`s wearing [far distance discovers, near distance recognise" s character. It balances the big and small angle of optical performance. It has a large reflection angle.
Knitting Reflective Garments Series,Knitting Reflective Garments,High Visibility Reflective Knitting Vest,Reflective High Visibility Polo Shirt
Daoming Optics & Chemical Co., Ltd , https://www.reflectives.nl