Increase in the proportion of hanging areas
At present, it is more and more common to set a hanging area in a custom closet. Now people's life is fast, and it takes a lot of time to stack clothes. At the same time, in addition to sweaters, there are fewer and fewer fabrics that are suitable for stacking. In these respects, designers often increase the proportion of the hanging area when designing the wardrobe. The proportion of the stacking area is gradually reduced. At present, the stacking area only accounts for about a quarter of the wardrobe, and is usually placed at the uppermost end of the closet.
Typically, a 2.4-meter-high wardrobe is used. Typically, the top layer is a stacking area with a height of about 40 cm. The lower part is designed as a hanging area, and is divided into upper and lower layers. Usually, the lower layer is larger than the upper layer, so that the angle of bending can be reduced when taking the clothes hanging below.
At the same time, the hanging area can also be converted into a stacking area during the season change. The clothes that need to be stored are placed in the storage box, and placed in the hanging area neatly, thereby realizing the storage requirements of the stacking area.
Wardrobe layout is subject to person
The first consideration for a custom closet is the user's needs. For example, the stacking magnifiers in the home are quilts and beddings. However, the two items are placed differently. The quilts are used only in winter every year, so they can be placed on the top floor of the wardrobe, and the bedding needs to be replaced regularly. It is reasonable to place it at a position 1.5 meters above the ground.
When designing the wardrobe, the designer often considers the interior layout of the wardrobe according to the gender, height, and occupation of the owner. For example, the height of the hanging area of ​​an ordinary female owner is usually around 1.1 meters, but if the height of the owner is high, the length of his clothes is relatively long, and the height of the hanging area in the closet needs to be increased.
In order to make the wardrobe more flexible, the floor and the clothes rail of the hanging area can be adjusted, such as a child's wardrobe. When the child is young, the position of the hanging clothes does not require a large space, and the stack can be stacked. The area is mainly, but when the child goes to school, the height increases rapidly. At this time, the height of the hanging area needs to be adjusted accordingly. The adjustable partition can solve such problems.
Metal basket
Cardigans are not suitable for hanging, because long-term hanging will be deformed. However, if you stack it in a closed drawer and take it out after two seasons in spring and summer, the wool will smell very heavy and wrinkle, so you can put it in a metal basket and keep it ventilated.
Trousers rack
In order to avoid wrinkles when trousers are stacked, you can use the trousers rack to hang. However, the utilization rate of the trousers rack is not high, and a 600 mm wide trousers rack can usually only hang 6 to 8 pants. The price of the trousers rack is usually hundreds of dollars. The designer suggested that if there is no special need, it is more economical to use the trousers rack to clamp the trousers and hang it in the hanging area.
storage box
A uniform storage box can be used to fill the corners of the hanging area, and can also be used to convert the hanging area to the stacking area. When choosing a storage box, you need to consider the size of the wardrobe and the height of the space.
Teflon Hight Pressure Die Casting Cookware
Process: Aluminum die casting
Surface:Teflon
Specification; custom
Package :as requirement
Application; for machine components or Led lighting fixture
Can OEM/ODM
Aluminum Casting Die home Application cookerware / waffle maker
|
Product |
|
|
Application |
Die casting part for cookware |
|
Used Die cast Machine (Depend on mould) |
Die casting machine 120 ton -800 ton |
|
Main Processes Flow (depends on part shape and requirement) |
Drawing / or Samples →Mould making →Die casting →Deburring →Drilling and Tapping →CNC Machining →Polish→Surface treatment →Assembly →Quality inspection → Packing →Shipping |
|
Production Flow |
Drawing/ or samples → Mould making →Die casting and other processes →Get samples and send samples to customer for approval → Mass Production ( casual inspection avoid unintentional situation) → QC → Packing →Shipping →Cycle to next order |
|
Surface Treatment (Optional by customer) |
Polishing, Sandblasting, Painting, Powder coating, Galvanizing, Chrome plating Anodizing , Real gold coating, Imitation gold, |
|
Drawing file ( 2D or 3D) |
In format of IGS, STEP, SLD,X_T, DXF, DWG, SAT, STL ,PDF |
|
Production Management |
ISO, 5S Management, Signboard Management, |
|
Our advantages |
In-house tool / mould making, mould design team , In- house die cast, Assembly line Exporting Experiences. |
Aluminum Casting Cookware & Pan
Teflon Pan,Cookware Pan,Aluminum Maker,Casting Aluminum Waffle Maker
Dongguan Hongge Hardware Technology Co., Ltd , http://www.honggecasting.com