It takes a while for things to be easy to break. It is difficult to avoid the cover of the toilet when the toilet is used for a long time, or it will hit the toilet cover cracked or it is broken. In this case, we are asking the professional to give us repairs, or automatic hand? How to replace the toilet cover? The following small series will work with you DIY to solve the bathroom installation problem, how to replace the toilet cover?
Method of replacing the toilet cover
Find the screw cap, remove it with a live hand, and replace it with a new one. Generally, the position of the screw cap is not easy to find, some are in the bright spot, and some are in the dark. In the dark, screw cap, open the cover on the side of the tank inside the toilet. Put it in your hand and touch it in the direction of the water tank. You should be able to touch it and see it is invisible.
Change the toilet cover method two
When replacing the toilet cover, you only need to remove the fixing bolt at the back of the toilet to replace it; you can operate it in the opposite direction during installation. Most toilet covers are not sized, and it is enough to adjust the two bolts during installation. However, it is also necessary to measure the size, the screw hole distance, the width and length of the toilet cover, and then purchase a new toilet cover for replacement.
Replace the toilet cover method three
In addition to the above two methods, Xiaobian recommends looking for a professional to change. Some workers who change the toilet cover offer free replacement, but to use the products they provide, in fact, the slightly higher price of the product already includes their labor costs.
If the problem with the toilet lid does not affect the normal use, in terms of saving, you still do not need to change the toilet lid. After all, replacing a toilet cover also requires money, in addition to the cost of finding people and personnel costs, so we do not look at the Xiaoyi DIY solution to the bathroom installation, how to replace the toilet cover?
HHCMS-200 carbon molecular sieves
CMS-200 is a new kind of non-polar adsorbent specially designed for extracting nitrogen-rich gas from air. It is suitable for separating nitrogen from air. It has a high adsorption capacity for oxygen and can separate nitrogen from air.
The most notable feature of the Carbon Molecular Sieve is its high gas-producing efficiency, especially the preparation of nitrogen with a purity of less than 99.5%.
It is widely used in large air nitrogen making equipment.
Project parameters
The diameter of:1.0-1.3 1.3-1.5
Packing density:≥660kg/m³
The intensity of particle:≥95
Compressive strength abrasion:≤1%
The moisture content:≤0.5%
Standard packing:20Kg/barrel. 40Kg/barrel. 130Kg/barrel
The adsorption time of test condition was 58s with an average pressure of 1-2s
|
Adsorption pressure |
Nitrogen purity (%) |
Yield (Nm3/ h.t.) |
Nitrogen recovery rate |
|
0.8MPa |
99.9 |
120 |
30 |
|
99.5 |
200 |
37 |
|
|
99 |
250 |
41 |
|
|
98 |
310 |
45 |
|
|
97 |
370 |
47 |
|
|
96 |
420 |
50 |
|
|
95 |
490 |
55 |
|
|
0.6MPa |
99.9 |
95 |
31 |
|
99.5 |
160 |
38 |
|
|
99 |
200 |
43 |
|
|
98 |
245 |
46 |
|
|
97 |
300 |
49 |
|
|
96 |
335 |
51 |
|
|
95 |
390 |
56 |
Pay attention to
1. The nitrogen production equipment can reduce the adsorption temperature to better show its excellent nitrogen production performance under conditions;
2. Pay attention to low temperature drying and seal preservation during storage;
Molecular Sieves Hhcms-200,Molecular Sieve Regeneration,Activate Molecular Sieves,Psa-Carbon Molecular Sieves
Zhejiang Changxing Haihua Chemical Co.,Ltd. , https://www.zjcxhhcms.com