[Milton Luo metering pump] Merton metering pump installation method is what? What are the installation steps? What are the installation skills? The installation method for the Merton Wheel dosing pumps is very important. If the dosing pump is not installed properly, it will affect the operation of the subsequent dosing pump. Therefore, this article Xiaobian introduce you to the main installation tips, installation methods and installation steps of the Merton metering pump, I hope for your help! Merton Roll Metering Pump Installation Tips - Installation Methods - The Merton Roll Metering Pumps Main Installation Steps Merton Roll Metering Pumps Installation Tips, Installation Procedures, and Installation Methods: 1. It is recommended that the suction lines be self-filling, The suction side is below the minimum reservoir level. If you must use suction lift installation, must be installed in the suction nozzle foot valve. 3 m water column mRoy A maximum allowable suction height. 0.9 m water column mRoyB maximum allowable suction height. 2, it is recommended to install filters in the suction line for inspection and cleaning. At the same time must have the necessary stop valve and pipe live for future maintenance. 3, in the Milton Rod metering pump outlet piping must be installed pulsation buffer, safety valve. If the pressure is lower than 3Bar, it is recommended to install a back pressure valve to prevent the pipeline from siphoning. 4, the suction pipe diameter must be greater than the metering pump inlet valve size. Determine the diameter size must consider the metering pump peak flow, pipe length and material viscosity and other parameters. When the outlet line is not equipped with a pulsation damper, the diameter of the pipe must also be determined with reference to the suction pipe diameter. 5, motor wiring must refer to the motor brand and operating instructions. At the same time pay attention to motor steering, viewed from the side of the fan, the motor rotates counterclockwise. 6, Disconnect the outlet line from the Milton Metering pump, or open the line vent valve. 7, according to the oil level instructions to join the oil, then the stroke adjusted to 0%. Start the metering pump to identify abnormal noise in the pump body. 8, the metering pump start / stop, repeated many times. Then set the stroke to 25% for 2 minutes; then set the stroke to 90% for 2 minutes. So repeated 3-5 times. 9, gradually increase the stroke to 100%, observe the metering pump outlet for material delivery, and the flow changes with the stroke adjustment. 10, close the pipeline exhaust valve or connect the outlet pipe, add material to the system. 11, Usually the factory setting Milton's metering pump built-in pressure relief valve set pressure is about 6Bar. Need to re-adjust the release pressure after connected with the system. Unscrew the yellow plastic cover near the filler neck and adjust the release pressure clockwise with an Allen key. The above is the introduction of the installation tips, installation steps and installation methods for the Milton Wheel metering pump, for your reference. (This article is published by Asia Fluid Network Editor, please indicate Asia Fluid Network,) (Editor: Li Juan)
It take a compressed gas as the power to form a high-speed jet to shoot glass beads on surface of work-piece that causes changes on surface and shape of the work-piece. Due to the glass beads` impact to surface, it makes the surface a certain of cleanliness and different roughness.
• It improves the mechanical properties of surface so as to enhance the fatigue-resistance of work-piece.
• It provides with parts-surface a controllable rough-surface to increase the adhesion with the paints, to extend the durability of the paints and it is also benefit to the flow and decoration of paints.
The glass bead can be produced based on the standard of countries or areas, such as EN1423/1424, AASHTO M247, BS6088, JIS R3301 and KS L2521 etc.
Blasting Glass Beads
Blasting Glass Beads ,Micro Blasting Glass Beads ,Blasting Glass Beads Road Marking,Reflective Blasting Glass Beads
CHIYE GLASS BEAD (HEBEI) CO., LTD , https://www.chiyeglassbeads.com
