In the modern bathroom space, many people like to put bathtubs. After we finish work, we can take a comfortable and relaxing bath. Do you know how the bathtub is installed? Today we have come to learn how to install the bathtub . I hope to help you.
Bathtub Installation Method Step 1: Test whether the water leaks.
Place the bathtub before the first water accessories, do water for 24 hours to see if the bathtub is leaking, pay special attention to the overflow. It's very difficult to close the water in 24 hours. Outside the bathroom, pour two buckets of water and try a good bathtub to get water. This is convenient.
At the time of actual installation, the bathtub was directly lifted into the bathroom and placed in the water. Since the width of the bathtub was just the same as the width of the bathtub when the water was changed, the size of the bathtub and the mixing of water was not correct. Note that the center point of the bathtub should be facing the center of the mixing water, otherwise it will be very difficult to see if the mixing faucet is installed in the future.
After the bathtub is lifted into the bathroom, it starts to put on and off the water fittings, fills the bathtub with water, and turns off the water to check for leaks. When the water flows over the overflow, the water in the bathtub flows out of the overflow. At this time, I Just squat on the floor, reach under the bathtub, touch the back of the overflow, and see if any water leaks out of it.
After the overflow test was passed, the next inspection of the water was closed. I chose to stand still and observe the tightness of the water. At the beginning, there was no problem. After about 10 minutes, the quiet bathroom was separated by a few seconds. The buzzing sound of water gulp, the water was not installed closed, there was leakage, decided to let go and reinstall the water. This time, the problem was discovered. The original copper pipe fittings that blisters took blisters had a trachoma in some areas and were tossed and leaked by us several times.
There is a bit of luck here. At the beginning, the bathtub was lifted into the bathroom. When the water was drained, the water was not afraid of the water. It was also a full cylinder of water. Under pressure, the sand eyes were pressed so that they would leak, if only a small amount. The water will not be able to withstand such a large pressure, and it will not leak at this time. If a skilled hydraulic worker may be very impatient with my test, this problem may not be discovered at that time. On the other hand, it also proves from the side that the hardware that is sent is indeed of good quality, and the hardware must be bought well.
It should be noted that the center point of the width of the bathtub is at the center point of the faucet. This point should be considered when the water is first changed. The width of the bathtub is 700*750*800. Once the water is changed to determine the size of the water, try to buy the bathtub as soon as possible, or change it later. Mixing water from the wall size is very difficult.
Bathtub installation method Step 2: Leveling the bathtub.
When placing the bathtub, take care that the other end of the water outlet is slightly higher than the end of the drain so that the sewage will not be discharged in the future. This depends on the circumstances. Observe that the bottom of the bathtub had a slope for draining water. Level the bathtub on the four sides and put it on the water test. As expected, the water quickly drained. The bathtub maintains a visually beautiful appearance without affecting the drainage effect.
Bathtub installation method The third step: sand filling.
Although the cast-iron bathtub is strong, its thermal conductivity is very fast. It should be used in Zhonghesha and it should be firmly laid on the bottom of the bathtub. Bricklayers also recommend the use of foam. Considering that foam is not as mobile as sand, it is ideal to fill all the gaps. In the process of filling sand, how to make sand not leak into the sewage pipe is a problem to be solved.
After all the placement work was completed, the water release test was performed again (this step was mainly to ensure that the backside of the bathtub did not leak water). After confirming it was correct, it waited for the bricklayer to lay the skirt.
Bathtub installation method Step 4: Leave the access port.
A 300mm wide 400mm hole is left at the water outlet, and one hole is cut to size. The board is made of water-repellent and anticorrosive wood (thickness 40mm) according to the size. The number of bricks and the number of rows arranged on the board are 903. The glue sticks the brick to the board. Extend the edge of the tile with a sealant and insert it into the box. This is to facilitate the overhaul of the bathtub drainage system in the future. In the bathtub skirt, for aesthetic considerations, all set aside 600 heights, give up other materials such as mosaics, bath skirts and the same brick under the wall brick, so to do, under the wall tiles, floor tiles, bath skirts are all One color, one material, very beautiful.
Bathtub installation method The fifth step: tiling.
Bathtub skirt tiles do not need to scratch the hair, build a red brick table, a layer of cement mortar on the surface, and then wait two days and then tiling can, tiling is very troublesome, due to the slope of the ground to stay, and the bathtub It's flat, so every big brick must be polished to different sizes. It's not possible to polish a lot at a time, it's easy to grind, and it's repeated. The top of the brick is to be inserted under the round edge of the bathtub so that it does not form an angle.
That's all a bathtub installed, I hope for your help, more information decorated, all in this site, so stay tuned.
More articles:
When Philippine special bathroom recommended Philippine special bathroom
Shower room brand line shower room which brand is good
Wrigley bathroom cabinet recommended Wrigley bathroom cabinet please
Bath barrel what material bathroom products to buy
Bathtub red brick
Led Ceiling Fan,Fanimation Ceiling Fans,Bedroom Ceiling Fans,Windmill Fan
JIANGMEN ESCLIGHTING TECHNOLOGY LIMITED , https://www.windfansummer.com